Advanced Rebuild Settings

Advanced Rebuild Settings

Icon:

Introduction

The software recalculates all Strings and sections when edits are made to any one string in the Vertical Grading Editor Window - this provides powerful dynamics in the intersection, cul-de-sac and road design processes. Unfortunately, when jobs get large, this dynamics can make the design of strings in the Vertical Grading Editor slow because the software is force recalculating all the other roads to ensure they are updated at intersections and other vertical/horizontal connection points.

These settings allow the designer to restore this previous calculation options. If dynamics is disabled, the methods to force updating of dependent objects is:

Rebuild all Models - rebuilds all models

Auto Model command - updates all road network objects (Road, Kerb, Cul-de-sac and Knuckle strings)

Auto Kerb Returns - updates all kerb strings to match horizontally and vertically to all Roads

Update All Roads - resamples and updates all Strings (this includes all general strings as well as all road network objects: Road, Kerb, Cul-de-sac and Knuckle strings)

Rebuild Options Explained

Do Not Update Network Strings Automatically: if this options is turned on, then the software will not recalculate kerb returns, cul-de-sacs or knuckles automatically when a Road string is edited (at or near an intersection with the Road string). When this option is ticked on, updating these string elevations can be achieved by running the Rebuild all Models command, Auto Model command or the Update All Roads command.

Only load string data when a CSD command is run: by default, if a design has been applied in a drawing, when the drawing opens the software will load up all the road data into the drawing, including updating models and displaying linework. If this option is ticked on, this startup updating is suppressed and the data is loaded only when an CSD software command is run

Only recalculate network strings when the VGE is closed: Intersection match-in, cul-de-sac connection, knuckle connection are only applied when the Vertical Grading Editor for a string is closed or data is added in the Design Data form, or when the Update Model button is selected on the Vertical Grading Editor > Model tab. The currently displayed cross section will update for the Vertical Grading Editor window. Surface models and linework updates when the Vertical Grading Editor window is closed.
Note: If the user has set the Auto Update to manual in the VGE window, then the model will not update on closing the Vertical Grading Editor window.

Auto Kerb Returns - Kerb Rebuild Off

When this command is run and Do Not Update Network Strings Automatically is enabled, the following form will display:

To maintain the settings but update the kerb return levels, select Update ON for this command.

Details

Upon selecting the command the following form is displayed:

Automatic updates

Do not update network strings automatically Tick on to disable updating of network strings. These strings will only update elevation/location when a rebuild is forced using the Rebuild Models, Auto Model, or Update all Road Objects command.

Only load string data when a CSD command is run Tick on to suppress the software from loading in all the string data when the drawing first opens

Existing Surface Calculations Controls whether sections are calculated 'on the fly' or saved to the data folders. Option also displayed in the Active Drawing Settings form

Redo: does not save the sections: they are always calculated

Save: saves the sections to file.

Redo requires more processor speed, so may slow on larger jobs.

Vertical Grading Editor

Only recalculate network strings when VGE is closed Tick on to disable linework and modelling updates when edits are made in the Vertical Grading Editor.

Plan Drafting Set to Manual to disable automatic updating of the linework.

Model Rebuild Set to Manual to disable automatic updating of the surfaces when a string is being edited in the Vertical Grading Editor.

Assign Layers Opens the Assign Layers command to enable user control over layers used in the linework display.

Surface

Logical Surface Swathe Width Sets the maximum width for calculations when Intelligent Sections are applied.

Maximum Contour cuts per triangle Type in a non-zero value to have the software limit the dispaly of triangles based on how many contours are displayed across that triangle. Useful for managing display where there are large elevation differences that would otherwise slow the surface draw routine.

Maximum DTM height different Type in a non-zero value to have the software limit the display of triangles based on a maximum surface height difference. Again, useful for managing display where there is a large elevation spike in the surface to reduce calculation and display time.

OK

Apply and exit.

Cancel

Exit the form without deleting any data.


Automatic updates
Do not update network strings automatically	Tick on to disable updating of network strings. These strings will only update elevation/location when a rebuild is forced using the Rebuild Models, Auto Model, or Update all Road Objects command.
Only load string data when a CSD command is run	Tick on to suppress the software from loading in all the string data when the drawing first opens
Existing Surface Calculations	Controls whether sections are calculated 'on the fly' or saved to the data folders. Option also displayed in the Active Drawing Settings form Redo: does not save the sections: they are always calculated Save: saves the sections to file. Redo requires more processor speed, so may slow on larger jobs.
Vertical Grading Editor
Only recalculate network strings when VGE is closed	Tick on to disable linework and modelling updates when edits are made in the Vertical Grading Editor.
Plan Drafting	Set to Manual to disable automatic updating of the linework.
Model Rebuild	Set to Manual to disable automatic updating of the surfaces when a string is being edited in the Vertical Grading Editor.
Assign Layers	Opens the Assign Layers command to enable user control over layers used in the linework display.
Surface
Logical Surface Swathe Width	Sets the maximum width for calculations when Intelligent Sections are applied.
Maximum Contour cuts per triangle	Type in a non-zero value to have the software limit the dispaly of triangles based on how many contours are displayed across that triangle. Useful for managing display where there are large elevation differences that would otherwise slow the surface draw routine.
Maximum DTM height different	Type in a non-zero value to have the software limit the display of triangles based on a maximum surface height difference. Again, useful for managing display where there is a large elevation spike in the surface to reduce calculation and display time.
OK	Apply and exit.
Cancel	Exit the form without deleting any data.